|
Linear
MultiCode Receiver AP-5
We are a Linear
Authorized
Sales & Service Distributor
AP-5: Wireless
Access Controller - Two Gate or Doors
Specifications
Installation Manual
Literature
Accessories and Compatible Models
 The AP-5 Wireless
Access Controller - Two Gate or Doors is designed for a broad
range of applications and can control one or two
The AP-5 Wireless Access Controller - Two Gate or Doors is
designed for a broad range of applications and can control one
or two door strikes, mag-locks, barrier gates, automatic gates,
or door operators. Its wireless design and small size fits a
variety of access control requirements.
The unit's built-in high-gain superheterodyne receiver picks
up transmitter signals from up to 500 feet away. The optional
EXA-2000 antenna can be used for additional range. Up to 480
Linear MegaCodeŽ transmitters and six Model MGT supervised
safety edge transmitters can be programmed into the AP-5's
memory. Up to 238 entry codes can be programmed for activation
by one or more MegaCodeŽ wireless keypads. The AP-5 will retain
its memory, even without power.
Three dry contact relay outputs are provided. One relay is
dedicated for access control, another dedicated for obstacle
detection, and the third programmable for either access or
obstacle. Access relays can be set for timed or
latch-on/latch-off toggle operation. The on or off toggle state
of a relay is maintained even after power interruption. For
entrapment detection, obstacle relays activate from MGT safety
edge transmitters and connect to the obstacle input of the
access device. OPEN REQUEST input terminals are supplied for
hardwired activation of the access devices with an external
pushbutton or keyswitch.
The AP-5 monitors each MGT safety edge transmitter for hourly
status reports, tamper signals, and low battery signals. A beep
will sound every 5 seconds if a fault occurs and the trouble
source can be displayed. An access transmitter must be activated
twice to trigger the access relay if a supervisory trouble
condition exists on any MGT transmitter.
The AP-5 can be powered from 12-24 Volts AC or DC. The Form C
relay outputs can switch up to 1 Amp each. An EARTH GROUND
terminal is provided as a recommended connection for maximum
lightning and static protection.
Features
- Ideal for gated communities, parking facilities, and
industrial sites
- Easy to set-up and use, up to 480 remotes can be
programmed with a few keystrokes
- Easy to add, suspend, and delete transmitters through
programming mode, no transmitter dip switches to set
- Supports 480 block coded transmitters or 238 individual
transmitters/wireless keypad entry codes
- Supports six fully supervised MGT safety edge
transmitters
- Three output relays; one for access, one for obstacle,
one programmable for access or obstacle
- High-gain superheterodyne receiver
- RF frequency: 318 MHz
- 4.45" W x 5.75" H x 1.5" D (without antenna)
- Order number: ACP00953
door strikes, mag-locks, barrier gates, automatic
gates, or door operators. Its wireless design and small size
fits a variety of access control requirements.
The unit's built-in high-gain superheterodyne receiver picks
up transmitter signals from up to 500 feet away. The optional
EXA-2000 antenna can be used for additional range. Up to 480
Linear MegaCodeŽ transmitters and six Model MGT supervised
safety edge transmitters can be programmed into the AP-5's
memory. Up to 238 entry codes can be programmed for activation
by one or more MegaCodeŽ wireless keypads. The AP-5 will retain
its memory, even without power.
Three dry contact relay outputs are provided. One relay is
dedicated for access control, another dedicated for obstacle
detection, and the third programmable for either access or
obstacle. Access relays can be set for timed or
latch-on/latch-off toggle operation. The on or off toggle state
of a relay is maintained even after power interruption. For
entrapment detection, obstacle relays activate from MGT safety
edge transmitters and connect to the obstacle input of the
access device. OPEN REQUEST input terminals are supplied for
hardwired activation of the access devices with an external
pushbutton or keyswitch.
The AP-5 monitors each MGT safety edge transmitter for hourly
status reports, tamper signals, and low battery signals. A beep
will sound every 5 seconds if a fault occurs and the trouble
source can be displayed. An access transmitter must be activated
twice to trigger the access relay if a supervisory trouble
condition exists on any MGT transmitter.
The AP-5 can be powered from 12-24 Volts AC or DC. The Form C
relay outputs can switch up to 1 Amp each. An EARTH GROUND
terminal is provided as a recommended connection for maximum
lightning and static protection.
Features
- Ideal for gated communities, parking facilities, and
industrial sites
- Easy to set-up and use, up to 480 remotes can be
programmed with a few keystrokes
- Easy to add, suspend, and delete transmitters through
programming mode, no transmitter dip switches to set
- Supports 480 block coded transmitters or 238 individual
transmitters/wireless keypad entry codes
- Supports six fully supervised MGT safety edge
transmitters
- Three output relays; one for access, one for obstacle,
one programmable for access or obstacle
- High-gain superheterodyne receiver
- RF frequency: 318 MHz
- 4.45" W x 5.75" H x 1.5" D (without antenna)
- Order number: ACP00953
|
